![]() 1 Select Account on the software main menu. ACTIVATE MACHINE We recommend you to register an account and active your printer to get fully access to functions of 3D printer. 5 Click “Print” to open the Printer Setting window. 4 The loaded model will appear on the Build Space. ![]() Z-Axis Y-Axis Extruder Unit X-Axis Build Platform Main Seat USB Connector Power Connector Power Switch Extruder Unit PLA Filament Sample 50g x 3 USB Cable Power Cable Build Plate Spare Screws Power Adapter Hex Key Plier Spool Holder Kits Calibration Sticker x 4 Scraper 0.2/0.4/0.6mm Nozzle Filament Guide Tube 1 2 3 Z-Axis Y-Axis Long Plug Short Plug 1 2 2 1 Nozzle Connector Account Back to Home Add a Model or Picture Print Initialize Calibration Maintenance Settings Share Skin Model Adjust- ment Wheel Build Space Too Low Just Right Too High Back Side Plastic Cable Buckle Mirror Delete Save Reset Move Scale View Wheel Menu Rotate Auto Place Undo Fix Errors Undo 2nd Level Menu 1 2 3 4 5 Current Nozzle Height Setting Value 1 4 0.30 5 0.00 6 0.00 9 0.00 8 0.00 7 0.10 Manual Auto Level Reset Nozzle Height 181 Move _ 0.00 _ _ Set Nozzle Detect Confirm Cancel 2 3 Manual Auto Level Reset Nozzle Height 181 Move _ 181.0 _ _ Set Nozzle Detect Manual Auto Level Reset Nozzle Height 181 Move _ 181.5 _ _ Set Nozzle Detect Paper LOAD AND PRINT A MODEL 1 Go to Add model “ + ”. When the printer buzz, insert the filament into the extruder unit gently. 5 Install the guiding tube, insert the filament into guiding tube. When the filament melting temperature is reached, the printer will buzz and begin to extrude. 2 Select the Material from the dropdown material list. For Example: If the nozzle position determined by the paper is 181.5, you have to set the nozzle height to 181.0 LOAD FILAMENT 1 Go to “Maintenance”. 5 Note the current nozzle height and deduct the value of it by 0.5mm and press “set” button to save the value as nozzle height (for printer with raft). At the correct height, the paper should be able to move freely but user should able to feel a small drag from the nozzle. 4 Put a paper in between the Nozzle and Platform, lower the nozzle and feel the drag be- tween paper and nozzle. 3 Use the + button to lower the Nozzle to close proximity of platform. 2 Press button 5 to move the Nozzle to the middle of the build platform. ADJUST THE NOZZLE HEIGHT 1 Go to “Calibration”. 5 Input the password for the Wi-Fi network Note: The computer and printer must be in the same WLAN (same SSID) before connecting. 4 Click the Network dropdown menu to select an available network. SETUP PRINTER 1 Click the Setting icon at the top right corner. Note: Initialization is required every time when the machine is powered on, this is in order to determine the correct position. Start to Print by clicking the print icon on the software main menu.Download and Install Cetus3D software:.2 Connect the Extruder Connector to the Extruder Unit. Install the Extruder Head to the Y Axis 1 Mount the Extruder Unit on the Y-Axis with 2 screws provided on the linear bearing. (2) It is only need to install three screws. There is no need to level the build plate. Note: (1) The device is pre-leveled in factory. Install Build Platform 1 Place the Build Platform on the Main Seat and align the three screw holes. 3 Plug the long plug into the socket on the Y-Axis. 2 Mount the Axis Assembly to the Main Seat with included screws. Install the Axis Assembly to the Main Seat 1 Plug the short plug into the socket on the Z-Axis. Not affiliated, just a happy user.For more information, please refer to 1. Needless to say, Im very pleased with this printer. (DUH) When the part was finished you could not tell where the power outage occurred. Then I reset the printer started it back up and after it initialized, a window popped up and said do you want to continue I said yes. So I immediately picked up the print head and smoothed out the soft plastic where it stopped. Okay, their software says the printer will remember where it was in the event of a power outage. ![]() About an hour and a half into that print job, the clumsy bastard I am, I tripped over the power cord and jerked it out of the printer. So I set up and started a 5 Hour print job. After it started printing I jerked the plug on the UPS. So I plug the Cetus into my UPS and started a small print job. I have a CNC hot wire foam cutter and a CNC router and I've always wondered if an uninterruptible power supply would keep one of them going in the event of a power failure. Their software needs some tweaking but there's been two updates in the last month so they are working on it. I've it over a month and I've used it almost every day. I just wanted to post my two cents worth about this Cetus3D printer.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |